Fabrication of the folding seating/bed

Fabrication of the benches/bed.... This is being done in the same was as the previous van build. They will fold up neatly into the walls and out of the way so that the whole back of the van can be used as a van to move stuff when required.

The bed is made from 25mm x 25mm x 1.5mm square section steel tubing.

Due to the benches being mounted at the same height as the rear door hinges we've had to create a wee step in the frame to allow clearance of the hinge.

Everything measured and cut ready to TIG weld together.

Two matching frames and folding feet made up.

A piece of 12mm plywood was then painted to create the tops of the benches and cut and screwed to the frame with self drilling screws.

Legs were bolted on with nylon spacer washers so theres no rattles and the powder coat finish doesn't get scratched once they're coated. The ends have plastic insets fitted.

A small lip was then added to the front edge of the seat which will allow the tables to drop in and sit on when they are folded out to form the bed base.

Seat bases are test mounted. All good. The front face of the legs will also get a carpeted sheet of thin plywood once they have been powder coated.

Everything's off to the powder coaters now... To be continued... 

Furry holes...

Next we worked on creating the furry cubby holes...

We used 12mm plywood , templated around the contours of the van, to create arm-sized cubby holes to access the storage spaces that we'll use to store our clothes.

Go go gadget arms....

Holes were cut to accommodate the door hinge and to allow access to the rear lights for changing bulbs...

A template for the upper portion of the 'wall' was also made (we still need to choose the type of material for this... see later post!) Shaped to fit the tapered contour of the top of the van. The white area you can still see will be carpeted.

For one side, we created some little furry compartments that will sit behind a raised edge, for storage of toiletries, portable speaker etc...

We've used a section of matching kitchen worktop to create a shelf on either side. Embedded into these shelves are wireless phone chargers, so you can simply sit your phone on the shelf to charge.

Charger stripped and the useful bit removed...

The hole was cut by router, set up on an offcut of worktop to leave approx 1mm of wood/laminate on the surface above the charger. The wireless charger was then bonded in using some hot melt glue. Power is supplied by a 12v to 5v usb converter which plugs into the charger.

Wooo we have walls and shelves!

Next the walls were upholstered in Veltrim, to make FURRY HOLES!
High temp spray adhesive applied to both sides...

Carpet then trimmed with a sharp Stanley blade and the process repeated on the front face carpeted too.

The edges of the furry cubbies were routered and knock-in edge trim was fitted for a professional finish.

Water tank

We had a custom underslung water tank made for the van by Barratt Tanks. It sits neatly tucked up to the chassis rails in front of the rear axle and is no lower than the exhaust or fuel tank. It holds approx 100L of fresh water, and 45L of waste grey water. We also had a CBE water level sender fitted so we can keep an eye on water levels from inside the van.

You can see here how the brackets attach and clamp the tank. A strip of thin foam was added between the tank and chassis to stop any chaffing or vibration.

It is filled via a standard hoselock connector, and the waste is drained via the other tap. These were mounted tucked up high on the sill and the waste tap was cut down to aid with ground clearance as we often take the van up rough dirt tracks. Pipes were then insulated and secured.

The breather was also extended and fitted with a wee stainless filter  to stop anything crawling in. 

Also did a bit of wiring and plumbing on our secondary 10L internal fresh water system. It consists of a 12v microswitched tap connected to a Whale submersible water pump that sits in a small water carrier. ideal for a quick night away in the winter when the main system is drained down for frost, or can be used with bottled water when we have filled the the main tank from a tap we cannot guarantee is quality drinking water.